Maintained! This is the X-2000R, the highest model in the X series. It boasts performance that surpasses the X-1000R, such as the CA (cobalt amorphous) head and newly designed equalizer amplifier, etc., and you can hear damped sound with little noise due to the DBX installation. ※No clampers. There is a feeling of use, such as paint peeling off the switch slightly and white stains on the power cord. Serial 315084 (Takasaki Atsushi)
Maintenance information: 2023.7.8 Maintained (pinch roller drive mechanism disassembly cleaning and oil application, pinch roller shaft cleaning and oil application. Capstan belt replacement and flywheel shaft cleaning and oil application, pinch roller shaft cleaning and roller check and cleaning treatment. PLAY operation key knob detachment repair treatment. Right reel motor internal cleaning repair and drive current control circuit part repair (transistor replacement, resistor replacement). Tension arm shaft cleaning, guide roller part cleaning, oil application, and tension arm joint replacement. Contact point cleaning treatment for FWD, REV playback and recording circuit switching operation switches and slide switches. Operation volume contact cleaning treatment. Head azimuth angle check and adjustment, FWD/REV playback level and recording level, recording bias check and adjustment, capstan motor speed check adjustment (within ± 0.5%). (Other than that, connector terminal solder reinforcement treatment, timer operation, DBX recording and playback operation tests are excellent.)
Accessories: manual copy ※ no clamper
Main specifications: 4 track, 2 channel stereo format W432 x H456 x D268 mm 21.0 kg
Maintained. This is the X-2000R, the best model in the X series. It boasts performance that surpasses the X-1000R, such as a CA (cobalt amorphous) head and a newly designed equalizer amplifier, and you can listen to damped sounds with little noise due to the DBX installation. There are stains and bumps on the exterior. Serial 20066 (Tamura Eiji)
Maintenance information: 2024.4.18 Maintained (flywheel detachable cleaning and capstan shaft cleaning oil applied, capstan belt replacement, grease applied to the foot wheel stator bearing part. Pinch roller drive mechanical disassembly cleaning and grease application, pinch roller cleaning and pinch roller shaft oil application, tape pass check. Head cleaning and head azimuth angle check adjustment. Left and right impedance roller detachment fall cleaning and oil application, left and right tension arm detachment cleaning and cushion replacement, tension sensor cleaning, and tension roller shaft cleaning oil application. Reel stand tension adjustment (FWD/REV-PLAY winding tension and tension adjustment during FF/ REW) playback and recording AMP electrolytic capacitor check and partial replacement, meter lamp, DBX display lamp replacement, replacement procedure due to deterioration of power supply protection resistance. MIC, LINE, OUTPUT volume contact cleaning Contact cleaning by detaching and disassembling the monitor SW, REC mode SW, tape bias selector SW, and DBX SW. Playback level check and adjustment, recording level and vise check and adjustment, DBX amplifier level check and adjustment, recording and playback tests are excellent. Left and right legs missing additional reference value W&F during self-recording and playback (0.02% (WTD))
Accessories: clamper
Main specifications: 4-track, 2-channel stereo format, W432 x H456 x D268 mm, 21.0 kg
Denon 10 inch reel deck. Direct drive. Maker maintenance completed on Feb.4 2012.
Professional studio model. 2 Track stereo. Magnetic 3 heads. Speed:19/33. Input/Output:XLR. W645xH1035xD755mm.
Maintained! 4-Track Open Reel Deck with Akai Reverse The crunchy electronic control logic is really pleasant. You can record again with a sharp and clear sound. When the power is turned on, the light of the meter lamp shines. The appearance has scratches, dullness, and rust floats. Serial 60710-20920 (Satoshi Yonejima)
Maintenance information: 2021.10.30 Maintained (Pinch roller drive mechanism cleaning and grease up treatment and oil application around the shaft. Capstan motor part due to bearing ball defect, grease up and motor shaft oil lubrication, capstan motor control semi-fixed volume cleaning, motor rotation speed with reference tape ± Adjustments were made within 0.5%. Tension arm cleaning and oil application to shaft, micro switch contact cleaning of left tension arm. Reel motor shaft oil lubrication and brake band cleaning. Removal due to adhesion of dirt on the substrate surface, replacement of jumper wires for defective jumper elements in the recording amplifier board, cleaning contacts of FWD/REV switching slide switches and contacts of operation volume ( LINE volume, MIC volume, pitch control volume, output level volume) AC cable replacement and power switch contacts deterioration check and cleaning, fuse board Cleaning and fuse inspection and terminal cleaning. Deckup ring and coupling capacitor exchange and semi-fixed volume exchange of playback equalizer amplifier and recording amplifier part, playback and recording head angle azimuth adjustment, playback level and recording level adjustment; Good recording and playback test by music source, reverse mode and timer start operation normal. The 10" reel clamper was disassembled and cleaned and applied with a small amount of oil as it did not move hard. Fixed the disappearance of counter characters. Reference value: W&F (WTD) 0.055% (However, it depends on the tape used.)
Accessories: cover, clamper, copy of instruction manual
Main specifications: 4 tracks 2 channels reversible tape speed 19/9.5 cm/sec Frequency characteristic 30 ~ 25,000 Hz tape selector 2 stage switching (wide range/low noise) W440 × H483×D256mm 21kg
Maintenance has been completed! 4-track open reel deck with Akai reverse The crunchy electronic control logic works comfortably. You can record with thick, clear sound quality. When the power is turned on, the light of the meter lamp shines. Appearance has small scratches and dullness. Serial 40212-00533 (Satoshi Yoneshima)
Maintenance information: 2021.12.5 Maintained (cleaning and grease up of pinch roller drive mechanism, pinch roller shaft cleaning and oil application. Capstan motor bearing hard ball replacement and grease up treatment, pitch control switching relay contact cleaning treatment and tape speed adjustment, tension arm mechanical disassembly check and oil on rotating shaft Application, tape sensing mechanism check (auto reverse operation check normal) Check reel motor driving force check at PLAY, contact cleaning treatment by detachment and disassembly of multiple switches for switching. Dirt removal and cleaning procedures for playback equalizers, recording amplifiers, and LINE amplifier substrates. Replaced the front panel REC mode switch. LINE amplifier, MIC amplifier part Replacement with transistor LowNoise and R11 constant change (Line-TRX4, MIC-TRX2, Rec-x1)) coupling of regenerative equalizer amplifier circuit Replacing the coupling capacitor in and. Recording amplifier coupling and decoupling capacitor replacement+22V line power supply control unit transistor replacement, bias oscillation circuit part electrolytic capacitor replacement, head cleaning and azimuth angle adjustment Check and adjust playback level, recording level, recording frequency characteristics. Color addition procedure because the red line of the right level meter scale has decolorization. MIC, LINE input volume cleaning, OUTPUT volume, pitch control volume cleaning. Capstan motor servo circuit signal processing transistor replacement, and electrolytic capacitor replacement, recording and playback sensory test by music source is good. (Other: residual noise - 55dB, recording and playback: W&F (WTD) 0.05%, Flutter (0.08%) However, it depends on the tape used)
Accessories: clamper, cover
Main specifications: 4 tracks 2 channels reversible tape speed 19/9.5 cm/sec Frequency characteristics 30 ~ 25,000 Hz tape selector 2-stage switching (wide range/low noise) W440 × H483 × D256mm 21kg
Maintenance has been completed! A full-fledged, high-performance open deck developed for audiophiles. The warm, thick sound quality with a texture is attractive. 2 tracks 19/38 cm speed, 4 tracks 2 channels can be used for playback only. The amplifier part and the mechanical part are separate types, and the motor part can be used even when laid down, so it is easy to use like a desktop type for business use. The appearance is dull and oxidized. Serial 120446 (Satoshi Yonejima)
Maintenance information: 2022.7.16 Maintained (mechanical part control circuit deterioration transistor replacement, Zener diode short replacement, fuse replacement. Tape tension arm cleaning oil application, capstan shaft oil application. Tape speed adjustment is checked with an internal frequency generator (FG) and a reference tape. Since the 2TR glass head is difficult to obtain, the 2TR regeneration head is a TEAC NOS product and can be installed as a substitute. →The frequency characteristics are maintained without changing the playback EQ. Compatible with 2TR head NOS products for TEAC decks. Head tilt check and adjustment, playback level and recording level check and adjustment, and recording playback test with music source are good. Other tape detection sensor lamp and REC mode indicator lamp replacement. (For reference: W&F (WTD) during self-recording playback; 0.05%, but it depends on the tape used)
Accessories: clamper
Main specifications: 3 motors, 2 speeds, stereo tape deck, 2 tracks, 2 channels, recording/playback, 4 tracks, 2 channels, playback, comprehensive frequency characteristics: 38cm/30Hz to 30kHz, 19cm20Hz ~ 20kHz Mechanical Part W505 × H402 × D310 mm 27 kg Amplifier Part W490 × H180 × D330 mm 8.5 kg
Maintained! Compatible with a variety of applications, from 2-track 19/38cm recording and playback to 4-track 19/9.5cm playback. A popular model that employs Technics's own isolated loop method. The unique mechanism of single capstan and double pinch roller achieves stable driving performance. The rich sound that responds to hearing is unique to an open deck. The appearance may be dull or paint loss. Serial RG810445 (Satoshi Yonejima)
Maintenance information: 2022.4.17 Maintained (power supply board, 13 electrolytic capacitors replaced. Reel servo board, 11 electrolytic capacitors are replaced. Replace 10 capstan servo board electrolytic capacitors Replaced 3 electrolytic capacitors on the control board. Replaced 50 pieces of playback recording amplifier board bias circuit part electrolytic capacitor Lever switch contact cleaning, deformation correction, and knob replacement. REC level volume and output level volume cleaning treatment. Operation key lamp replacement procedure. Counter mechanism cleaning treatment, belt replacement. Tension roller cleaning, reversing roller disassembly cleaning. Head block cleaning and head changeover switch disassembly cleaning. Signal level check and adjustment for playback system and recording system. Each playback recording head cleaning, polishing treatment. Head housing part connector and harness replacement. (Self-recording and playback W &F (WTD) 0.02%)
Accessories: clamper
Main Specifications: 2 Tracks 2 Channels (Recording/Playback) 4 Tracks 2 Channels (Playback) Maximum Usage Reel No. 10 Tape Speed/9.5/19/38cm Isolated Loop Mechanism Quartz Capstan direct drive by PLL method W456 × H443 × D257 mm 23 kg
* Recording and playback tests have been performed, but there is a luster in the volume. Since it cannot be maintained in the future, we will sell it as it is. 2 tiger 38 cm open reel deck Time counter with gapless punch in punch out function and 5 point locating function. A model equipped with various editing functions such as edit queuing. The appearance has a feeling of use corresponding to the year (Fujisawa Yukishi)
Maintenance Information: 2022.2.17 Recording/Playback Tested There is a gulp in the volume.
Accessories: Instruction manual
Main specifications: 2 tracks 38cm specification W483 × H444 × D180mm 28kg
Maintained. 4 track, 2 channel, 19/38 cm specification, the technology from that time was generously introduced to improve performance, make it possible to push out low frequencies and clear sound quality, and you can also feel the analog feel. Please enjoy the model that enables high-quality recording and re-recording unique to Lvox. There is a feeling of use on the exterior due to dirt, rust, small scratches, etc. (Kobayashi Hitoshi)
Maintenance information: 2022.12.14 maintained (motor drive block capacitor replacement 3 pieces, reel motor drive logic circuit repair, counter mechanism cleaning and belt replacement, 50 deteriorated electrolytic capacitors and 17 semi-fixed volume exchanges, capstan motor speed adjustment and running speed confirmation with test tape, mother board selector switch pattern and slide multiple switch contacts Cleaning, input level volume, headphone volume, LINEOUT volume contact cleaning, headphone relay contact detachment cleaning, head azimuth angle adjustment, playback level and recording level and recording bias adjustment, and playback level are adjusted 257 nWB/m as 0 VU. The level of LINE OUT at 0VU is 0.775V at 0DM. The peak indicator on this unit is adjusted so that it lights up at +6 dB. Good recording and playback tests and MIC amplifier tests. 10-inch reel adapter repair, self-recording and playback W&F (WTD) 0.02%, residual noise erased during normal tape recording - 48dB (linear measurement))
Accessories: 2 clampers, empty reel
Main specifications: W452 x H414 x D207 mm 17 kg