Unused item! Power supply/heater transformer custom product primary: 100V secondary: 5V/3A, 6.3V/2.5A, 600-550-535-0-80-535-80-535-550-600V/0.17A, CT-5V/1.5A × 2 W122 x H87 x D105 mm 5.3 kg (actual measurement, not including protrusions) mounting nut with original box (Kojima Yosuke)
Accessories: mounting nuts, original box
Input transparent sale primary: 10 KΩ secondary: 60 kΩ boost ratio 1:2.5 W 24 x H35 mm 60 g/piece (actual measurement, not including protrusions) with white box (Kojima Yosuke)
Accessories: white box
The dirt, tobacco smell, and feeling of use are conspicuous, so it is currently sold. An HX series higher-level machine that effectively controls space. It's a speaker for home theaters, but the sharp sound is attractive (Daiki Goto)
Maintenance information: 2024.5.7 operation confirmed
Accessories: none
Main specifications: 3-way bass reflex type (anti-magnetic) 20cm cone woofer x 2, 13cm cone midrange, 3cm dome tweeter 6Ω 364 x 1102 x 397 mm 32.5 kg
The price has been reduced. 2024/2/23 sales price 35,000 yen KRK powered speaker equipped with a Class D power amplifier. The amplifier section is equipped with an equalizer to help adjust room acoustics (Sasaki Shota)
Maintenance information: 2024.2.23 Operation confirmed
Accessories: power cable, original box
Main specifications: 2-way 145 W playback frequency band 42 Hz to 40 kHz input balance, standard jack W225 x H339 x D284 mm 7.6 kg
※The spikes are out of stock, so it's cheap. A perfectly sized round top plate is used for B&W's “805 Series”. This speaker stand is made of lightweight magnesium alloy with a high vibration absorption rate (Shota Sasaki)
Accessories: none
Main specifications: top plate W226 x D304 mm bottom plate W238 x D317 mm height 600 mm weight 14 kg
B&W bookshelf sized speakers It is equipped with a Nautilus tube and Kevlar cone unit from the higher series. This size is sufficient for clean mid to high ranges and low frequencies without any habit. It goes well with modern sauces. The jumper plate is dull, and there is a small scratch on the upper corner (Daiki Goto)
Maintenance information: 2024.5.7 operation confirmed
Accessories: instruction manual
Main specifications: 2 way 16.5 cm woofer 8 ohm bi-wiring connection possible W204 x H356 x D244 mm 6.1 kg
Granite speaker stand by Ishizo Unkei. It has been mirrored and has a careful finish. It contributes to damping the vibration and tightening of the sound of small speakers (Ryo Mizusaki)
Accessories: none
Main specifications: top plate W160 x D220 mm bottom surface W220 x D270 mm height 605 mm weight 17.3 kg
Unopened brand new (opened for photography) arm lifters that can smoothly operate tone arms without lifters, such as the RMG309i and RMG212i orthophone. Can also be used on the company's old models with a rotating shaft diameter of 20 mmφand RMA types for A shells (Oikawa Tetsuji)
Accessories: original box
※Overall, there is dullness, rust, and scratches, and there is a feeling of use, so it is inexpensive. A classic MC boost transformer. With 2 input systems, the impedance can be switched to 3.40 ohms, and a PASS line is included, so you can freely enjoy various cartridges and tone arms. (MIZUSAKI Ryo)
Maintenance information: 2024.1.27 Operation confirmed
Accessories: none
Main specifications: MC boost transformer input 2 systems switchable, primary impedance 40 ohm, 3 ohm switching, secondary impedance 4 kΩ boost ratio 1:10 frequency characteristics 10 Hz to 100 kHz, W97 x H65 x D155 mm, 800 g
Power supply/heater transformer primary: 100V secondary: 6.3V/4A, 7-6.3-5-5-6.3-7V/5A × 2 W130 × H150 × D130 mm 8.1 kg (actual measurement, not including protrusions) There are scratches in places (Yosuke Kojima)
Accessories: none
RCA cable 1.0m pair revision B type signature series There is little dramatization in the tone, but you can enjoy a spectacular sound field feeling as if the speaker size has been larger by one size or more. There is dullness on the plug (Kojima Yosuke)
Accessories: none
Power cable 3.0 m A power cable that uses the company's KS-00 cable, uses an AET PSE-018V2HG as the outlet plug, and an AET PSE-320HG as the inlet plug. Compared to the predecessor, it is a monitor and high-resolution oriented model that has excellent high-frequency reproduction capability and resolution, and transmits sound images more clearly than ever before (Kojima Yosuke)
Accessories: none
The 1.5m PSE standard power cable is sharp, but the increase in S/N speed is not deliberate and I like it. When I held it, it was heavy and had a sense of luxury. There was rubbing and dirt around the plug (Kojima Yosuke)
Accessories: none
The disposal price has been reduced! (Member discounts are not applicable) 2024/4/18 sales price 79,800 yen with MA15 woofer fixing bracket! An original product. A floor-type enclosure that uses a rear-loading horn system. The interior has a folding horn structure with a total length of 2 meters, making it possible to reproduce powerful bass far exceeding its size. The exterior has chipped corners, scratches, repair marks, and paint peeling. Serial 11154 (Tomoho Asaine)
Accessories: MA15 woofer grill net
Main specifications: hole diameter 365 mm, screw pitch 420 mm backroad horn compatible speakers 2205, 2225, E140 minimum playback frequency 50 Hz main material particle board+Yonematsu laminated plywood (front baffle/road horn) W603 x H12 x D603 mm approx. 54 kg
The price has been reduced. 2024/5/3 sales price 27,800 yen This is a high-resolution D/A converter. Dual monaural configuration, compatible with DSD 5.6 MHz and PCM192 kHz/32 bit USB inputs. You can easily enjoy the world of high-resolution audio from high-resolution sound source playback software installed on your computer. The output is equipped with an XLR balanced output in addition to the RCA output. Furthermore, these audio output levels can be selected from fixed, variable, and output off (Oikawa Tetsuji)
Maintenance information: 2024.5.3 operation confirmed (playback confirmed up to PCM192 kHz/DSD 5.6 MHz, COAX/OPT playback OK, each output playback confirmed)
Accessories: power cable
Main specifications: PCM data sampling frequency 32K, 44.1K, 48K, 88.2K, 96K, 176.4K, 192 kHz W215 × H61 × D238 mm 2.0 kg
Power transformer primary: 100V secondary: 7.5-6.3-0-6.3-7.5V/3A (2 circuits) W90 × H121 × D90 mm approx. 3.6 kg (actual measurement, not including protrusions) There is a fine bruise (Kojima (Yosuke)
Accessories: none
※The woofer cap has a dent, so it's cheap. Denon tall boy speaker It is a model with high cost performance for both theater use and pure audio use. Since it has a double woofer configuration, you can enjoy low frequencies larger than its size. It plays any genre, such as jazz, pop, or rock. The exterior is dull overall, paint is chipped on the front corner, and there are conspicuous line scratches on the back side (Mizusaki Ryo)
Maintenance information: 2024.5.16 sound output confirmed
Accessories: jumper plate
Main specifications: 3-way 4-speaker bass reflex crossover 2kHz, 13kHz 90dB W270 x H1130 x D325 mm 24.8 kg
An enclosure that seems to be for Sansui's old system component speakers. The lattice box with legs reminiscent of JBL's Baron and Bicount is really fashionable. The lattice on both the left and right is out of the frame. There are traces of internal remodeling (Fujisawa Koshi)
Accessories: None
Main specifications: opening diameter 212mm (screw pitch 240mm), aperture diameter 110mm (countertop 170mm, screw pitch 140mm), opening diameter 95mm (for bass reflex port/wood screw pitch 118mm), aperture diameter 70mm (Countertop 92mm, Screw Pitch 104mm) 14mm Particle Board, Veneer Finish W500 × H665 × D430mm 15kg
Output transparent sale push pull output 35W primary: 8kΩ secondary: 4-8-16Ω usage: 7189 app, etc. W82 x H72 x D82 mm approx. 1.6 kg/piece (actual measurement, not including protrusions) The plate is often scratched, printing is erased a lot, and there are paint floats due to rust in places (Kojima Yosuke)
Accessories: none
Pair tube KT88 compatible ball American metal base measurement value 58/52 (rejection value 44) There is getter burn and loss on one side, and there is dullness on the base on the other side ※The pair is judged based on the gM value measured by the testing machine TV-7 (Kojima Yosuke)
Accessories: none
A rare Rotel thin phono equalizer. It has a flat, neutral tone with no distractions, and I like how simple it is to use. There are small scratches, dullness, and the electrical outlet has changed (Oikawa Tetsuji)
Maintenance information: 2024.4.29 Operation confirmed
Accessories: instruction manual, original box
Main specifications: input sensitivity MM: 2.5 mV/47 kΩ MC: 210 mV/100 Ω size W440 × H72 × D195 mm weight 3.1 kg
The stylus is good, but since the cantilever is curved, it is inexpensive. A mono-only cartridge with a traditional 33 series body. Play mono records clearly with a pick-up that is only horizontally oriented. It has vertical compliance and is optimized for recurrent mono editions in the stereoca era. The range is wider than Denon's DL-102 and you can feel the expansion (Fujisawa Yukishi)
Maintenance information: 2023.8.29 Operation confirmed
Accessories: needle cover
Main specifications: MC type needle pressure 2.3 to 2.7 g (2.5 g standard) Muku round needle high hardness duralumin cantilever PCOCC coil anti-vibration rubber “honeynight” impedance 10 ohms 6.9 g
Pair tube, triode, metal base, made in America, with original box, the size of the glass tube is different on the left and right, but the internal structure is the same ※The pair is determined based on EM values measured with the SENCORE TC-162 test machine (Kojima Yosuke)
Accessories: white box
Large triode sold per unit measured IP value: 50 mA (the best standard IP value for this amplifier is 50 mA) There is a getter burn with the original box ※ I checked the sound output and measured the plate current value with the test amplifier, and it was determined that the operation was good (Kojima Yosuke)
Accessories: original box
The disposal price has been reduced. Member prices are not applicable. 2023/10/23 sales price 29,800 yen ※Currently sold. Comes with a special case! Portable headphone amplifier with built-in D/A converter. DSD256 (11.2 MHz/1 bit) PCM supports native playback of up to 768 kHz/32 bit. Please enjoy the sound quality unique to a thick mojo in the mid to low range. There is dullness and a feeling of use (Sasaki Shota)
Maintenance information: 2023.10.23 Operation confirmed
Accessories: original box
Main specifications: output level 35 mw/600 ohm, 720mw/8 ohm, output impedance 0.075 Ω, dynamic range, 125 dB input system, 3 optical systems, 1 coaxial x 1, microUSB x 1, 2 output systems, headphone jack x 2, charging time, approx. 5 hours continuous operation time, approx. 8 hours W82 x H60 x D22 mm 180 g
Pair tube direct heat triode tube, white base, made in Russia, measured value 80/80 (rejected value 58) with original box ※ pair is determined based on gM values measured by testing machine TV-7 (Kojima Yosuke)
Accessories: original box
There is no problem with the operation, but it will be handed over as is. Yamaha subwoofer. You can easily enjoy powerful sound. The high-cut filter allows you to listen in the desired range, so the range of uses also expands. The exterior has a slightly raised part on the top plate, and there is a scratch on the back corner (Mizusaki Ryo)
Maintenance information: 2024.5.9 sound output confirmed
Accessories: none
Main specifications: A-YST method anti-magnetic amplifier output 250W playback frequency band 20Hz to 160Hz high-cut filter frequency 40Hz to 140Hz continuously variable W340 x H432 x D370 mm 17 kg
Mono exclusive MC cartridge. It's not flashy, but it stretches and makes a gentle sound that is pleasant. There is a feeling of use such as dullness (Daiki Goto)
Maintenance information: 2024.5.13 operation confirmed
Accessories: original box, instruction manual
Main specifications: MC type 0.5 mV needle pressure 2.5 to 4.5 g dead weight 5 g
A speaker stand with the same texture as the company's NS-1000M. The angle of the midplate can be adjusted to 4 positions according to the low frequency characteristics of the room and speakers. It is ideal for medium speakers such as the NS-1000M. The exterior has scratches and dullness. (FUJISAWA KOSHI)
Accessories: No accessories
Main specifications: W370 x H250 x D290 mm 6.5 kg
The disposal price has been reduced! (Member discounts are not applicable) 2024/5/13 sales price 30,000 yen model number, convenient for small amplifiers, etc. such as unspecified steel satin finish audio racks, spike specification LINN products, etc. There is a feeling of use on the exterior such as small scratches and dullness (Asaine Tomoho)
Accessories: none
Main specifications: size W395 x H540 x D395 mm shelf board 350 x 350 mm between shelves 105 mm weight 11.7 kg (actual measurement)
Self-made enclosure. The woofer opening is about 340 mm in diameter, the horn opening above it is 450 mm x 266 mm, the upper opening is 260 mm x 134 mm, and the tweeter part is about 60 mm in diameter. Shipping costs will be estimated separately (Oikawa Tetsuji)
Accessories: none
Main specifications: plate thickness 25 mm W800 x H960 x D580 mm 54.1 kg (actual measurement)
※It is cheap because it is in poor condition due to numerous modifications. Heavyweight horizontal audio rack It's sturdy, so it's fine even if you put a super dreadnought analog player on the top plate. The inside is slightly larger, so even slightly larger full-size equipment can be stored. Since there are many modifications such as the exterior, attaching a copper plate to the upper right shelf, attaching a tile mat to the bottom, and attaching a handle to the tray, etc., the shelf on the right side does not come off, and a feeling of use such as dullness and abrasions can be seen (Kobayashi Hitoshi)
Accessories: none
Main specifications: Overall measurement W1200 x H535 x D572 mm inner dimensions on one side (without shelf board) W530 x H430 x D (top plate 560, medium plate 470, lower stage 560) mm top plate thickness 45 mm shelf board thickness 23 mm weight 69.85 kg
Pair tube, 6L6GC compatible ball, high reliability tube, made in America lot: 8526/8526 measured value 44/42 (rejected value 25) with replacement box ※ pair is determined based on GM values measured with test machine TV-7 (Kojima Yosuke)
Accessories: replacement box
Pair tube ambient heat beam tube made in America, measured value 42/40 (rejection value 25) with original box (the claws on one side of the box are missing) *Pairs are determined based on gM values measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Pair tube, triode, metal base, made in America, comes with a box, is inexpensive because there are fewer gutters and there are burns ※Pairs are determined based on EM values measured with the SENCORE TC-162 test machine (Kojima Yosuke)
Accessories: white box
Pair tube, metal, brown base, made in America, measured value 66/64 (rejected value 44) with original box (some written), sticker is attached to the base part, and there is a getter burn ※ The pair was determined based on the GM value measured with the test machine TV-7 (Kojima Yosuke)
Accessories: original box
Power transformer primary: 100V secondary: 280-250-0-250-280V/AC0.12A 5-6.3V/2A 6.3V/1.5A ×2 W83 × H105 × 78 mm 2.7 kg with original box (Kojima Yosuke)
Accessories: original box
Self-made enclosure for 38cm units. An ALTEC 416-8C was installed. It is sturdy and heavy. There is a feeling of use on the exterior, such as scratches, paint chips, paint on the back, and screw holes in the top plate. ※Shipping costs will be estimated separately (Mizusaki Ryo)
Accessories: saran net
Main specifications: W660 x H995 x D465 mm (including casters) woofer aperture 360 mm φweight 51.1 kg (actual measurement)
*Currently sold. Comes with enhanced power supply OBH-2. Creek MM phono equalizer. Although it has a compact body, it lets you hear bouncy low frequencies with good pitch. The response of the power lamp is slightly poor, but this is the current situation (Oikawa Tetsuji)
Maintenance information: 2024.5.20 Operation confirmed
Accessories: enhanced power supply OBH-2
Main specifications: Dimensions W100 x H62 x D125 mm Weight 360 g
Power transformer primary: 100V secondary: 5V/3A, 2.5-6.3V/5.2 A x 2, 6.3V/3A, 360-400-450V/170mA W120 x H95 x D105 mm 5.3 kg (not including protrusions) There are abrasions and line scratches in places (Kojima Yosuke)
Accessories: none
Pair tube VT-115 equivalent tube, high durability tube, metal tube, tea base, measured value 46/44 (rejected value 25) with white box ※Pairs are determined based on GM values measured with the TV-7 testing machine (Kojima Yosuke)
Accessories: white box
Pair tube VT-115 equivalent tube, high durability tube, metal tube, tea base, measured value 48/46 (rejected value 25) with white box ※Pairs are determined based on GM values measured with the TV-7 testing machine (Kojima Yosuke)
Accessories: white box
The disposal price has been reduced. Member prices are not applicable. 2023/12/10 sales price 25,000 yen*Since the output terminal has been remodeled to an XLR terminal, it is inexpensive. It is a pretty niche product that uses 2 stereo amplifiers so that it can be used like a mono amplifier. Actually, it seems to be a product intended for use with the company's 405-2. There is a lot of dullness on the exterior due to aging (Fujisawa Yukishi)
Maintenance information: 2023.6.4 sound output confirmed
Accessories: none
Main specifications: W80xH47xD140mm approx. 1.0 kg/unit
※Sold as 1 piece output transformer for single output 7W hammer tone color primary: 5 kΩ/7 kΩ secondary: 4/8/16 Ω W56 x D50 x H80 mm 0.79 kg/piece with original box (Kojima Yosuke)
Accessories: original box